[. . . ] 10 Installing the VS-700 Control Surface Plug-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MIDI Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 MIDI Controllers/Surfaces Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Loading the VS-700 Plug-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the "Found New Hardware Wizard" appears, click [Finish]. 7) and re-install the driver from the beginning of the procedure. 8 SONAR VS-700C Getting Started Guide 14. The Found New Hardware Wizard dialog will appear. This window should look similar to the following picture. Verify that the New Hardware Wizard reads: "This wizard helps you install software for: VS-700C". Choose "Install the software automatically (Recommended)" and click [Next]. If the Wizard displays "UM-1" instead of "VS-700C", go back to step 1 and make sure your DIP switches are setup properly. 15. When the screen indicates "Completing the Found New Hardware Wizard", click [Finish]. When the VS-700C Setup indicates "Installation has completed", click the [Close] button. 9 SONAR VS-700C Getting Started Guide Windows Vista Users 1. IMPORTANT: The VS-700C needs to be configured for "Stand-Alone Mode" to be used without the VS-700R I/O. To configure the VS-700C for stand-alone mode, locate the "Setting" area on the back containing eight DIP switches. Carefully move DIP switch 1 to the "on" position (facing up). DIP switches 2-8 should be set to the default "off" position (facing down). Disconnect all USB cables except those for a USB keyboard and/or USB mouse, if used, then start up Windows. 3. Disable any antivirus programs that could prevent or cause problems with driver installation. 4. Insert the "SONAR V-STUDIO 700 CD-ROM" into your computer's CD/DVD-ROM drive. The "VS-700 Setup" AutoRun will appear if you have AutoRun enabled. Right-click on "My Computer" from the desktop or the Start menu 7. Right-click the CD-ROM and/or DVD-ROM drive labeled "VS-700" and select "Explore". Open the folder labeled "Drivers". 10 SONAR VS-700C Getting Started Guide 9. Open the folder labeled "Vista32" if you are running a 32-bit installation of Vista. If you are running a 64-bit installation of Vista, open the "Vista64" folder. 11. Launch the VS-700C Driver Setup by double-clicking on "Setup" or "Setup. exe". The installer will prompt you to connect a USB cable from the VS700C to your computer and to power on the VS-700C. The screen will indicate "VS-700C driver has been installed successfully". [. . . ] By registering, you will gain access to free updates, technical support, tips, and exclusive upgrade offers. 15 SONAR VS-700C Getting Started Guide MIDI Device Settings 1. Make sure that the VS-700 is connected to your computer, and then launch SONAR. Click Options | MIDI Devices to open the "MIDI Devices" dialog box. In the "Inputs" and "Outputs" lists, select only the CONSOLE (VS-700C). Your screen may not resemble the image above if you have additional MIDI devices installed on your computer 4. [. . . ]